<rt id="kaoi2"><small id="kaoi2"></small></rt>
<sup id="kaoi2"></sup>
<acronym id="kaoi2"><small id="kaoi2"></small></acronym><rt id="kaoi2"><small id="kaoi2"></small></rt>
Installation and maintenance of mosquito control lamp
專欄:Industry information
發布日期:2018-12-03
閱讀量:2440
作者:佚名
收藏:
Do not use ceiling hanging flies killing lamp in food processing scale.Do not use click-on flies killing lights in places where explosions occur.III.

According to the function of killing flies, flies can be divided into electric shock type and sticky trap type. The principle is to use light to lure flies and insects to approach the lamp tube, so that insects can contact the high-voltage fence or sticky flies paper near the lamp and electrocute or stick them to kill flies and insects.

In the process of electric shock, the fly-killing lamp shoots the dead insects and scatters them everywhere, which may cause further pollution. The sticky-trap fly-killing lamp catches insects through the built-in sticky tape, which does not form secondary pollution, and is conducive to monitoring the variety, quantity and trend of insect pests. The sticky-trap fly-killing lamp is usually used indoors. In order to improve the efficacy, the flies control lamp should be accurately placed.

I. Selection of Fly-killing Lamps

Ultraviolet light should be used as light source, and the wavelength should be 330 to 350 nanometers.

There is a strong ultraviolet light source (i.e. high wattage), and a reflector behind it.

Equipped with a washable collection basin.

Select different mosquito control lamps according to the environment.

II. Device of Fly-killing Lamp

Place flies-killing lights along insect-bound roads such as entrances, doorways or other bottlenecks and halls.

The first fly control lamp should be imported at an interval of about 3.6 meters (but not less than 3.6 meters).

Install a number of fly control lamps according to the area of the site.

In order to make the function of flies killing lamp better, the interval between flies killing lamp should not exceed the scale of 12 to 15 meters.

Fly control lamps should be distributed evenly in the site.

Install the fly-killing lamp at the height of the fly, i.e. about 1.5 meters above the ground.

As far as possible, place the fly-killing lamp in the direction where its lights can be seen on all sides, but it should be prevented from being placed near the windows and doors, so as to prevent the lamp from attracting outdoor insects.

Fly-killing lamps should not be placed in direct sunlight or near mercury lamps with sodium vapor lamps, because they emit a lot of ultraviolet light. The influence of standard incandescent lamp and light tube on the efficiency of fly control lamp is only slight, even No.

Fly control lamp should be placed in warm place, so it is easier to attract flies.

Place a fly-killing lamp at the entrance of the food production scale and keep a minimum interval of 1.5 metres (preferably 4.5 to 6 metres) with uncovered food. Only low hanging wall type fly control lamp can be used. Do not use ceiling hanging flies killing lamp in food processing scale.

Do not use click-on flies killing lights in places where explosions occur.

III. Notices in the Use of Mosquito Control Lamps

The lower end of the fly-killing lamp should be more than 50 cm above the ground, and the top should be more than 50 cm above the ceiling. The height of the middle end should be about 1.8 meters above the ground.

When the flies killing lamp is used, closing other lights can improve the killing effect.

A fly control lamp is installed every 20 square meters.

Fly control lamp should prevent directly facing doors/windows and other situations that attract outside flies.

In the environment of food treatment, the use of electric shock lamp should be prevented, and the dead insects should be blown up by electric shock.

It is not allowed to use electric shock type fly-killing lamp in the place where explosion occurs simply.

The function of flies-killing lamp is closely related to the life of lamp tube. Fly paper and lamp tube should be replaced regularly.

3. Maintenance of Fly-killing Lamp

It is necessary to collect insect corpses in a basin at least once a week, preferably twice a week.

Light source and electric netting should be cleaned at least once a month.

Ultraviolet light should be replaced once a year, preferably before spring.

According to the manufacturer's instructions for the use of products, to ensure that the fly control lamp can achieve maximum results.

上一頁:Great gathering of mosquito control tactics
下一頁:How about the effect of ultrasonic mosquito repellent?
久久久久人妻一区精品色|特级a∨无码在线观看|免费岛国a级毛片无码|国产aⅤ无码精品专区|一级久热爱精品视频|中文字幕乱码人在线视频1区|国产偷国产偷精品孕妇
<rt id="kaoi2"><small id="kaoi2"></small></rt>
<sup id="kaoi2"></sup>
<acronym id="kaoi2"><small id="kaoi2"></small></acronym><rt id="kaoi2"><small id="kaoi2"></small></rt>